Make the building safe before you touch the water: power off at a panel you can reach dry, nobody wading near live circuits. Then photograph everything, get standing water out as the river drops, and treat river water as contaminated, which means most soaked porous material leaves rather than dries.
Key takeaways
- River flood water is treated as contaminated, so soaked carpet, pad, lower drywall and insulation generally come out instead of being dried in place.
- Pumping a basement faster than the ground water outside falls can load the walls and floor, so the water comes down in stages.
- The National Weather Service puts flood stage on the Fox River at Algonquin at 9.5 feet and the record stage at 12.70 feet, set on 23 April 2013.
- In July 2017 about 800 buildings in McHenry County were reported underwater and McHenry, Lake and Kane counties were declared disaster areas.
- Photographs taken before anything moves are the part of the claim that cannot be recreated later.
- The Chain O'Lakes reach behaves differently from the river at Algonquin, and a forecast crest there is not a forecast for your street.
What should you do in the first hour?
Deal with electricity first, then documentation, then water. If the panel or any outlet is submerged, stay out and have the supply cut. Once it is safe, photograph and film every room before a single item is moved, because that record cannot be made again.
Do not wade into a flooded basement to see how bad it is. Water that has reached outlet height, a submerged furnace, or a panel you cannot reach from a dry step are all reasons to stop at the top of the stairs. Gas appliances that have been under water are not relit by the homeowner. None of this is caution for its own sake; it is the difference between a damaged basement and an injury.
After that, the useful hour is spent on the record and the phone. Wide shots of each room, close shots of the tide line on the walls, the serial plates of anything mechanical that went under, and a short walking video. Then make the calls: your insurer, and a restoration crew. Crews here are dispatched 24/7 as fast as one is available, and in a regional flood the queue forms early.
Is Fox River flood water clean or contaminated?
Treat it as contaminated. River flood water has crossed roads, yards and storm drains, and in a big event it mixes with whatever the sanitary system has given up. Materials that absorb it are removed, not dried, and the surfaces behind them are cleaned before drying starts.
This is the single biggest difference between a river flood and a burst pipe, and it is the one homeowners most often argue with, because the water in the basement can look clear. What makes it a different category is where it has been rather than how it looks. Carpet and pad, the bottom courses of drywall, batt insulation in the stud bays and particle board furniture are the usual casualties.
What generally stays is the structure itself: framing, concrete, block, solid wood that can be cleaned and dried and read with a meter. A crew will cut drywall above the wet line, pull the insulation out of the bays, clean, and then dry the cavity with air moving through it. It looks drastic on the first day and it is the reason the house is habitable in a month.
How high does the Fox River actually get here?
At Algonquin the National Weather Service puts flood stage at 9.5 feet, and the record stage is 12.70 feet on 23 April 2013. July 2017 brought the river near or above that record, with reported crest figures that conflict, so no single 2017 number is given here.
Those numbers are worth knowing because they tell you how little margin there is between a river that is merely high and one that is in the houses. Three feet separates flood stage from the record, and both of the biggest events on this reach in living memory sit in that band. A gauge reading on its own does not tell you whether your street floods, but it tells you which side of the line the river is on.
The McHenry dam gauge was projected to reach its own 2013 record in 2017 as well, which is a reminder that the flood is a whole-river event rather than a town-by-town one. Crests arrive at different hours in different places, and a reading taken upstream is a warning for downstream rather than a description of it.
| Marker | Stage | Note |
|---|---|---|
| Flood stage | 9.5 ft | National Weather Service |
| Record stage | 12.70 ft | 23 April 2013 |
| July 2017 | Near or above the 2013 record | Reported crest figures conflict |
| Chain O'Lakes, 2017 high | 8.03 ft | A different reach with its own behavior |
When can pumping start, and why not all at once?
Pumping starts once the water outside is falling and there is somewhere safe to send it. Emptying a basement while the ground outside is still saturated loads the walls and floor from the outside with nothing pushing back, so the level is brought down in stages.
That is the part most people have never been told, and it is why a crew may deliberately leave water in the basement for a while. The water inside is holding the walls up against saturated soil. Taken out too fast, a block wall can bow and a floor slab can lift, and a structural repair is a far worse outcome than another night of standing water.
Where the water is sent matters as well. Pumping into a sanitary cleanout is not acceptable, and pumping straight against the foundation puts the same water back through the wall. The discharge needs to run away from the house, to a point where it will drain rather than pond, and in a river flood that point can be a long way off.
How long is the window before mold becomes part of the job?
Short. Mold needs moisture, warmth and material to feed on, and a wet finished basement supplies all three. The honest answer is that every hour of delay costs material, which is why extraction and air movement start before anyone discusses the rebuild.
No fixed number of hours is given here because the real window depends on the temperature, the materials and how much air is moving. A cold basement in March buys more time than a humid one in July. What does not change is the direction: the longer wet insulation sits in a closed stud bay, the more likely it is that the cleanup becomes a remediation job as well as a drying job.
This is also why opening the building up matters more than running a fan at the puddle. Air that cannot reach the wet material does nothing for it. A crew's first hours go into removing what traps water and setting equipment so the air moves across the surfaces that are still holding it.
What comes out and what can be saved?
Carpet, pad, soaked insulation, wet particle board and drywall below the wet line generally go. Framing, concrete, block, solid hardwood and most hard furniture can usually be cleaned, dried and kept, provided readings confirm the drying.
The judgment is about whether a material can be cleaned all the way through. A hard, non-porous surface can. Carpet pad cannot, however long you run a fan at it. Documents, photographs and textiles sit in the middle: some can be dried and salvaged, and the ones you care about should be set aside early rather than discovered in a skip.
Mechanical equipment is its own decision. A furnace, water heater or air handler that went under water is assessed by a trade rather than restarted, because the controls and the burner assembly are the parts that fail quietly afterwards. Note the model and serial numbers while they are still in place and photograph the plates.
| Material | Usual outcome | Why |
|---|---|---|
| Carpet and pad | Removed | Cannot be cleaned through after contaminated water |
| Drywall below the wet line | Cut out | Holds water and hides a wet cavity |
| Batt insulation in wet bays | Removed | Holds water longest behind a dry-looking wall |
| Framing, block, concrete | Cleaned and dried | Can be cleaned and verified with readings |
| Furnace or water heater submerged | Assessed by a trade | Controls and burners fail after submersion |
Is the Chain O'Lakes different from the river reach?
Yes. The Chain sits upstream on its own storage and reacts differently: its 2017 high was 8.03 feet, a 2008 flood damaged about 500 homes in northwestern Lake County, and a 2004 Fox Lake flood affected about 60 homes. A crest forecast there is not a forecast for Algonquin.
If you are in Fox Lake, Ingleside or around Wauconda, the water that reaches you is lake-system water held and released across a chain of connected lakes, and it can stay high for a long time after the rain stops. Downstream at Algonquin and Cary the river is narrower and more responsive, so the shape of the hydrograph you should care about depends on where you live.
In April 2026 flooding on the Chain was forecast above 2017 levels; the final crest was not checked for this guide, so no outcome is claimed. The practical point stands either way: find out which gauge describes your water, and treat a number from the other one as background rather than a warning.
What does the week after the water look like?
Extraction, then removal of what cannot be saved, then equipment running with moisture readings taken at each visit, then the structure declared dry against a target. The rebuild is quoted after that, not during it.
Expect noise and expect the basement to be unusable. Air movers and dehumidifiers run continuously, and switching them off overnight to sleep sets the drying back by more than the quiet is worth. Expect a technician back to take readings and to move equipment as the wet area shrinks, because a dryer on day five belongs somewhere different from where it stood on day one.
Keep your own record alongside theirs: the dates, the readings you are shown, what left the building. In July 2017 the flooding was big enough that Algonquin cancelled Founders' Day for the first time in 57 years, and in a regional event that size, the households with their own documentation were the ones who could explain their claim without relying on anyone's memory.
Frequently asked questions
Can I run my own pump and save the restoration fee?
You can pump, if it is safe to do so and the electrical situation is sound, and getting the level down is genuinely useful. What a pump does not do is dry the building or clean what contaminated water touched. The failure case is a basement that looks dry with soaked insulation behind intact paint, which surfaces weeks later as a smell and then as a remediation job. Pump if you safely can, then have the moisture read before you reline the walls.
Is flood water covered by my homeowner's policy?
Policies differ, and rising surface water is often handled differently from a burst pipe inside the house, so the only reliable answer comes from your own policy and your insurer. What you should do regardless is document before anything moves, keep the inventory of what is discarded, and start mitigation rather than waiting for an answer. Sitting on a wet basement to protect a claim usually damages both the house and the claim.
How do I know whether the water was river water or sewage?
Often you do not, and that is why a crew treats an uncertain source as the worse category until it is settled. Clues include where the water first appeared, whether a floor drain or a toilet was involved, and whether the whole street went under at once. Tell the technician exactly what you saw and in what order. The scope depends on the answer, so a guess made to keep the job smaller is not in your interest.
Should I open the windows or close the house up?
Once equipment is running, the building is usually closed so the dehumidifiers can work on a controlled volume of air. Before that, ventilation helps if the outside air is drier than the inside air, which in a humid Illinois summer it often is not. Follow the crew's instruction on this rather than a general rule, because it depends on the weather on the day and on which stage the drying has reached.
What if the river comes up again before the house is dry?
It happens on this reach, and a crew plans for it by keeping equipment off the floor where it can and by prioritising removal over rebuild while the risk is live. Nobody reinstalls drywall in a basement that may take water again in the same week. Watch the gauge that describes your own location, keep the sump discharge clear, and tell the crew if a second rise is forecast so the sequence can be adjusted.
Sources
This guide is general information for McHenry County homeowners, not a substitute for an on-site inspection. Prices are estimates. See our disclaimer.